FORK TINES FULL
FORK TINES FREE

Refer table above and descriptions below for all rating information for each type of Fork Arm available. The rating is for an individual Fork Arm and should beĭoubled to provide a total safe working load. Some very early forks have survived with four prongs (or tines), others with three. Each Fork Arm is stamped on the side with the relevant information. Tine definition, a sharp, projecting point or prong, as of a fork.

When fitting Fork Arms ensure that the marking on the Fork Arms is compatible with the forklift rating. Type FA25-107 = Fork Arm 2.5 tonne SWL/ pair at 500mm load centre x 1070mm blade length. When ordering Fork Arms ensure correct parts are ordered (refer table below).Į.g. Some of the signs you can look out for during your pre-operation inspection are bent blades, surface cracks and bend fork-tips. However, failure to use them the right way usually leads to premature wear and tear or irreversible damage. The fitting of Fork Arms with a lower rating than the forklift truck could lead to failure, resulting in injury or death. The forklift tines are very critical for the efficient operation of a forklift. Always ensure that the rating of the Fork Arm is equal to or exceeds the rated lift capacity of the fork truck. Random testing has been carried out in accordance with AS2359.1 Clause 6.5.įork Arms are supplied in a range of capacities and lengths. Product not sold or manufactured by Horst Welding.Stamped on each Fork Arm – 750 x 500 representing 750kg at 500mm LCĬombined capacity for the pair = 1500kg at 500mm load centreįork Arms (or forklift tines) supplied have been designed in accordance with AS2359.1.Product that in the judgment of Horst Welding has been misused by the user.Horst Welding Warranty will not apply to: All defective products must be returned to Horst Welding in Listowel, Ontario unless directed otherwise by a representative of Horst Welding. This bevel is used to allow the tines to slide under the tread of a.

FORK TINES FULL

The design makes it easy to pry meat out of a lobster tail, for example. Tire Forklift Tines are tines having a full length bevel along the inner face of the fork. These narrow utensils have three tines and are used for eating crustaceans and shellfish. With over 1.6M products and 24/7 customer service we have supplies and. They are the only fork to be placed to the right of the plate. Looking for Super Reinforced Fork, SST, 12In Tines Find it at. All claims must be accompanied by a photograph of the defective product. Oyster forks are the great rule-breaker of proper utensil placement. All claims must be discussed with a representative of Horst Welding prior to any repairs or warranty will be void. Repair and labor (at an agreed rate) will be performed by a dealer for Horst Welding or a repair shop designated by Horst Welding. Recommended repairs and cost are to be discussed with, and agreed on, by an authorized Horst Welding representative. If the pliers aren't large enough to fit around the fork, lay the fork on its side and gently hammer. Heavy duty fork tines add versatility to pallet fork carriages for moving a wide variety of palletized construction site materials. Aim to gently bring the tines back into alignment. Squeeze the tines with a pair of pliers, placed over the cloth. Distributor/dealer must notify Horst Welding of the defect by phone, fax or email. Place the fork into warm water to warm it up.

The closer tines reduce the amount of wasted shavings. The buyer by the acceptance of the equipment will assume all liability for any damages that may result from the use or misuse by his employees or others. Fine Tines Pitch Fork is designed for use with pelleted and sawdust bedding to get the small stuff. The company shall have no liability for related damages of any kind. The company’s liability shall be limited exclusively to replacing or repairing without charge, at its factory or elsewhere, at its discretion, any material or workmanship defects that become apparent within one year from the date on which the equipment was purchased. But the company shall not be liable for special, indirect, or consequential damages of any kind under this contract or otherwise.

FORK TINES FREE

All equipment is sold subject to mutual agreement that it is warranted by the company to be free from defects of material and workmanship.

Fork tines